Outdoor Wireless Bridge 5.8G Point to Point CPE335 Access Extender PTMP WiFi PTP Network 300Mbps 3KM Transmission Distance 14DBi High-Gain Antenna 24V PoE Power Supply 2 Pack

Rating:
100% of 100
$99.99
In stock
SKU
CPE335

CPE335 Wireless Birdge is an outdoor high power and high-performance CPE to Extend your Network, which works at 5G frequency. It supports Point to Point and Point to Multi-Point wireless connection; The transmission speed between 2 bridges max is 300Mbps; The highest network speed that can be achieved max is 100Mbps; The transmission distance max is 3 km /1.86 miles

  • CPE335 dialing wireless outdoor bridge is outdoor high power and high-performance 5.8G 300Mbps point to point CPE. The transmission speed between 2 wirelss WiFi bridges max is 300Mbps. The highest network speed that can be achieved max is 100Mbps. To achieve the CPE function, one needs to act as a receiver and the other one as a transmitter.
  • Ethernet WiFi bridge pairing can be done by dialing without having to access the GUI, avoid the complex setup program, save much human work and cost, make the long-range wireless coverage, data transmit and wireless monitoring simple and professional. 2-pack CPE has been pre-configured/complete the pairing, you do not need to pair again, if you need to change the parameters, you can dial to pair.
  • 3KM Transmission distance: 3 km (visible unobstructed environment), actual application distance should be less than 3KM. Built-in 14DBi directional antenna can significantly improve the transmission and reception performance of wireless signals. Trees will not block the transmission speed of the point to point internet wireless bridge, suitable for warehouses or garages next to your house.
  • Low Interference & Outdoor Waterproof: 5G frequency makes long range wireless bridge has better anti-interference performance, good compatibility, and strong anti-adjacent channel interference, better than 2.4 G traditional CPE; It can automatically adjust to the optimal transmission speed according to the actual signal strength and transmission distance. CPE335 network bridge is very suitable for outdoor use, with rain, dust, and antifreeze characteristics.
  • Access CPE via PC: Point to point bridge is manageable through the WEB browser interface. Before accessing, please modify the IP address of the computer to the same network segment as the CPE, which is very important; then enter the IP address of the CPE in the browser, and enter the account password to access and set. If you can’t set it up, please let us know.

CPE335 Outdoor Wireless Bridge Kits

CPE 335 Wireless Bridge

CPE335 5.8G Wireless Bridge with 300Mbps and 1.86 Miles Data Transfer Range

CPE335 wireless bridge kits is one pair of outdoor high power and high performance 300Mbps wireless bridges, which works at 5GHz frequency. Supports Point-to-Point and Point-to-Multipoint wireless connection. It is more stable and higher speed and anti-interference performance than 2.4GHz wireless bridge. Moreover, it is easy to manage through the WEB interface.

CPE335 Kits Function:

  1. the device can works as Auto pairing mode: simply to use, connect both bridges to the PoE power adapter to start working, it will auto pair in few minutes. Customize mode: need connect the bridges to the computer through ethernet cable, and configure the master & slave parameters, this mode suit for experienced technician.
  2. the device can use for share internet networks to a long distance, output WiFi hot point, also can use for transmit the long ranges IP cameras' video stream to the control center without complicated wiring connection.
  3. Auto pairing mode works for point-to-point access connection, customize mode can configure the point to multiple point connection.

CPE355 Kits Application:

The CPE335 kits is great to extend your home internet network to another building without wire connection, you can share your network to your barn garage, warehouse, workshop or small store near to your home, it also works for enterprise to share the internet from different office, workshop, warehouse and etc.

We offer a pair of wireless bridge in the package, we need to set one works as master mode, and another works as slave mode.

Wireless Bridge Master & Slave Set:

1.Master Bridge Set

Move the mode switch to "A" position, the device works as master mode

2.Slave Bridge Set

Move the mode switch to "B" position, the device works as slave mode

Share your internet network from one building to another without complicated wire connection

Internet network share

Extend your internet network to another building without wire connection, works as outdoor wireless access point

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the router through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the computer or router by another ethernet cable

The master bridge transfer data to slave bridge works as point to point mode to extend network access to another house, office, building for internet surfing. The master bridge also output WiFi hot point, such as outdoor access point, you can open the WiFi connection setting on your cellphone, or laptop, you will find the WiFI name CPE5G_5Gxxx, enter the password to get access.

The access password is pre-programmed, it is different depend on what channel the wireless bridge working, but only change the last two or three numbers.

For example: the WiFi hot point name is CPE5G_5G161, and the default password is zllinkcpe123456161, if the name is CPE5G_5G153, the password will be zllinkcpe123456153, the last three numbers of the password is match to the last three numbers of the name, zllinkcpe123456 is the same, you can find the password with a little bit change for different channel.

Point to point video surveillance connection diagram

point to point video surveillance

Transfer the video stream from the slave bridge to the master bridge, DVR receive & manage the video stream

Wireless Bridge Master & Slave Set:

1.Master Bridge Set

Move the mode switch to "A" position, the device works as master mode

2.Slave Bridge Set

Move the mode switch to "B" position, the device works as slave mode

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the switch by another ethernet cable

Point to Point video surveillance, expand your video surveillance range, easily management all your surveillance camera in one DVR system without complicated wiring. Transfer your video surveillance network IP cameras data from another building to your DVR, easy to management all the cameras in one system.

Point to multiple point video surveillance connection diagram

Point to multiple point video surveillance

One master bridge and multiple slave bridge connection together by computer configure to management different place's IP cameras to one DVR system

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the IP cameras by another ethernet cable

Install the slave bridges face to face to the master bridge, and the direction angle no more than 60 degrees, this connection need login into computer to configure the IP address for different slave, please read the user manual for details.

In this way, you can easy transfer the network camera video streaming from different buildings to the DVR of the control center, point to multiple point function is great for you to monitoring multiple buildings without complicated wiring.

CPE335 Product Interface

CPE335 Interface

The wireless bridges work by two modes, auto pairing mode with pre-programed suit for newbie, customize mode suit for experienced user.

Auto pairing mode:

connect it to the PoE power adapter, the Power LED turns green on, system is power on, when the both bridges all are power on, it will auto pair in few minutes, the pairing and LAN status LED light all turns green on. the digital LED indictor display the numeric in red color.

you can press the "RST" button to change the channel to find a good frequency without interference, short press the button, the LED indicator will display the numeric "0","1","2","3"..."F" one by one, and change in cycle, each numeric means a different frequency, you can find the details on the user manual.

Customize mode:

at this mode you need connect it to computer and set the different IP address and working mode, short press the "RST" button will not functional at this mode, but you can press and hold this button over 10 seconds to reset to factory mode.

 

point to multiple point connection wireless bridge channel adjust WPA Encryption

One Master Bridge to multiple Slave Bridges

One bridge works as master mode, the other two or more bridges works as slave mode, all the bridges need to install as face to face, for multiple point connection, the slave bridge direction angle no more than 60 degrees.

Matching the master and slave bridge channel

Adjust the slave bridge channel to match to the master bridge, the both devices will be auto paired in few minutes.

WPA2-PSK Encryption

The bridge output WiFi hot point with WPA2-PSK encryption to keep your network in safety, do not worry your privacy to be exposed.

 

Parameters

Model:

CPE335

Network Interface:

10/100Mbps 2 * LAN Port

Data Rate:

11a: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps / 11n: 7.2M, 14.4M, 21.7M, 28.9M, 43.3M, 57.8M, 65M, 72.2M, 14.4M, 28.9M, 43.3M, 57.8M, 86.7M, 115.6M, 130M, 144.4Mbps

Power Supply:

POE 24V 1.0A

Antenna:

14DBi (5180~5825MHz)

Transmission Range

3KM / 1.86 miles

Waterproof:

IP65

Dust-proof:

Support

Working temperature:

-4℉~158℉

Dimensions:

250mm * 90mm * 65mm

/ 9.8'' * 3.55'' * 2.56''

Weight

1.1kg / 38.8 oz (A pair)

Outdoor wifi extender | access point | outdoor access point | wireless access point | point to point wireless bridge | wireless bridge | wifi antenna | wifi extender | wifi access point | wifi bridge | wireless bridges | wifi booster | wireless access point | wifi adapter | wifi bridge | wifi bridge | outdoor access point

 

Write Your Own Review
You're reviewing:Outdoor Wireless Bridge 5.8G Point to Point CPE335 Access Extender PTMP WiFi PTP Network 300Mbps 3KM Transmission Distance 14DBi High-Gain Antenna 24V PoE Power Supply 2 Pack
Your Rating