Wireless Bridge 5.8G Access Point To Point PTMP WiFi PTP Outdoor Network CPE 2KM Transmission Distance With 12DBi High-Gain Antenna 2 LAN 100MBps Ethernet Port 24V PoE Power Supply CPE220 2 Pack

$89.99
In stock
SKU
CPE220
CPE220 Wireless Bridge is an outdoor high power and high-performance CPE Kits to Extend your Network, which works at 5G frequency. It supports Point to Point and Point to Multi-Point wireless connection; The transmission speed between 2 bridges max is 300Mbps; The highest network speed that can be achieved max is 100Mbps; The transmission distance max is 2 km /1.2 miles
  • Point to Point Outdoor Wireless Bridge - 5.8G 300Mbps point to point CPE allow you to extend wifi outdoor between 2 building and transfer data.The max of transmission speed 2 wireless wifi bridge is 300Mbps.The max of network speed canbe achieved is 100Mbps.Master bridge and slave bridge play a role of transmitter and receiver which make CPE function work perfectly
  • [Point to Multiple Point Video Surveillance]: the DVR system which connects to the master bridge to receives the IP cameras which connects to the slave bridges' video stream for different building or place, management different building's IP cameras in one system without complicated wire connection, easy to cover river, lake, highway, railway with wireless transmission.
  • [Easy to Installation]: the both wireless bridges will auto pairing in one minutes when connects it to the PoE power adapter, pre-programed point to point mode, no need to connect to the computer for configure, save your time and great for the newbie who do not need to learn a lot of internet knowledge, the master bridge output WiFi hot point, you can enter password to get access, extend the WiFi access coverage up to 1.2 miles in 60 a degree angle of the front direction
  • [Long Range Transmission Distance]: the wireless bridge can reach up to 2KM transmission distance(Barrier-free), provide up to 100Mbps wired network speed, built-in 12DBi directional antenna can significantly improve the transmission and reception performance of wireless signals. the trees will not block the transmission speed of the wireless bridge, suitable for warehouses or garages next to your house.
  • [Widely Applications & Outdoor Weatherproof] - IP65 rated weatherproof housing that ensures continued operation on harsh outdoor environments,point to point or multiple point connection for outdoor access point, internet network extender, remote video surveillance usage, to share your WiFi to your Barn Garage Store and Warehouse. Enterprises can use this bridge to share the network from different offices, workshops, warehouses etc.

CPE220 5.8G Wireless Bridge Kits to Extend your Network

wireless bridge

Extend your network from one building to another without wire connection CPE220 5.8G Wireless Bridge with 300Mbps and 1.2 Miles Data Transfer Range

CPE220 wireless bridge kits is one pair of outdoor high power and high performance 300Mbps wireless bridge, which works at 5GHz frequency. Supports Point-to-Point and Point-to-Multipoint wireless connection. It is more stable and higher speed and anti-interference performance than 2.4GHz wireless bridge. Moreover, it is easy to manage through the WEB interface.

CPE220 Wireless Bridge Kits Function:

A. the device can works as Auto pairing mode: simply to use, connect both bridges to the PoE power adapter to start working, it will auto pair in few minutes. Customize mode: need connect the bridges to the computer through ethernet cable, and configure the master & slave parameters, this mode suit for experienced technician.

B. the device can use for share internet networks to a long distance, output WiFi hot point, also can use for transmit the long ranges IP cameras' video stream to the control center without complicated wiring connection.

C. Auto pairing mode works for point-to-point access connection, customize mode can configure the point to multiple point connection.

The CPE220 kits is great to extend your home internet network to another building without wire connection, you can share your network to your barn garage, warehouse, workshop or small store near to your home, it also works for enterprise to share the internet from different office, workshop, warehouse and etc.

We offer a pair of wireless bridge in the package, we need to set one works as master mode, and another works as slave mode.

Wireless Bridge Master & Slave Set:

1. Master Bridge Set

Move the mode switch to "A" position, the device works as master mode

2. Slave Bridge Set

Move the mode switch to "B" position, the device works as slave mode

Point to Point WiFi Internet Access

access point

Share your WiFi from one building to another without wire connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the router through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the computer or router by another ethernet cable

The master bridge transfer data to slave bridge works as point to point mode to extend network access to another house, office, building for internet surfing. The master bridge also output WiFi hot point, you can open the WiFi connection setting on your cellphone, or laptop, you will find the WiFI name CPE5G_5Gxxx, enter the password to get access.

The access password is pre-programmed, it is different depend on what channel the wireless bridge working, but only change the last two or three numbers.

For example: the WiFi hot point name is CPE5G_5G161, and the default password is zllinkcpe123456161, if the name is CPE5G_5G153, the password will be zllinkcpe123456153, the last three numbers of the password is match to the last three numbers of the name, zllinkcpe123456 is the same, you can find the password with a little bit change for the different channel.

Point to Point Video Surveillance

video surveillance connection

Extend your video surveillance network cameras range, connect all the cameras on one DVR system

Wireless Bridge Master & Slave Set

1.Master Bridge Set

Move the mode switch to "A" position, the device works as master mode

2.Slave Bridge Set

Move the mode switch to "B" position, the device works as slave mode

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the switch by another ethernet cable

Point to Point video surveillance, expand your video surveillance range, easily management all your surveillance camera in one DVR system without complicated wiring. Transfer your video surveillance network IP cameras data from another building to your DVR, easy to management all the cameras in one system.

Point to multiple Video Surveillance

point to multiple point

Point to multiple point video surveillance network camera system connection

Wireless Bridge Connection

1.Bridge A Connection - Master Bridge

Step 1: the LAN port of the PoE Adapter connect to the DVR through an ethernet cable.

Step 2: the PoE port of the PoE adapter connect to LAN port of the master wireless bridge by another ethernet cable.

2.Bridge B Connection - Slave Bridge

Step 1: the PoE port of the PoE adapter connect to the LAN port of slave bridge through an ethernet cable

Step 2: the LAN port of the PoE adapter connect to the LAN port of the IP cameras by another ethernet cable

Install the slave bridges face to face to the master bridge, and the direction angle no more than 60 degrees, this connection need login into computer to configure the IP address for different slave, please read the user manual for details.

In this way, you can easy transfer the network camera video streaming from different buildings to the DVR of the control center, point to multiple point function is great for you to monitoring multiple buildings without complicated wiring.

Wireless Bridge Interface

wireless bridge interface

The CPE220 wireless bridge kits works by two modes, auto pairing mode with pre-programed suit for newbie, customize mode suit for experienced user.

Auto pairing mode:

connect it to the PoE power adapter, the Power LED turns green on, system is power on, when the both bridges all are power on, it will auto pair in few minutes, the pairing and LAN status LED light all turns green on. the digital LED indictor display the numeric in red color.

you can press the "RST" button to change the channel to find a good frequency without interference, short press the button, the LED indicator will display the numeric "0","1","2","3"..."F" one by one, and change in cycle, each numeric means a different frequency, you can find the details on the user manual.

Customize mode:

at this mode you need connect it to computer and set the different IP address and working mode, short press the "RST" button will not functional at this mode, but you can press and hold this button over 10 seconds to reset to factory mode.
wireless bridge one to more wireless bridge channel WPA Encryption

One Master Bridge to multiple Slave Bridges

One bridge works as master mode, the other two or more bridges works as slave mode, all the bridges need to install as face to face, for multiple point connection, the slave bridge direction angle no more than 60 degrees.

Matching the master and slave bridge channel

Adjust the slave bridge channel to match to the master bridge, the both bridges will be auto paired in few minutes.

WPA2-PSK Encryption

The bridge output WiFi hot point with WPA2-PSK encryption to keep your network in safety, do not worry your privacy to be exposed.

Parameters

Model:

CPE220

Network Interface:

10/100Mbps 2 * LAN Port

Data Rate:

11a: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps / 11n: 7.2M, 14.4M, 21.7M, 28.9M, 43.3M, 57.8M, 65M, 72.2M, 14.4M, 28.9M, 43.3M, 57.8M, 86.7M, 115.6M, 130M, 144.4Mbps

Power Supply:

POE 24V 1.0A

Antenna:

12DBi (5180~5825MHz)

Transmission Range:

2KM / 1.2 miles

Waterproof:

IP65

Dust-proof:

Support

Working temperature:

-4℉~158℉

Dimensions:

170mm * 90mm * 60mm / 6.67'' * 3.55'' * 2.36''

Weight:

0.7kg / 24.7 oz

Outdoor wifi extender | access point | outdoor access point | wireless access point | point to point wireless bridge | wireless bridge | wifi antenna | wifi extender | wifi access point | wifi bridge | wireless bridges | wifi booster | wireless access point | wifi adapter | wifi bridge | wifi bridge | outdoor access point

Write Your Own Review
You're reviewing:Wireless Bridge 5.8G Access Point To Point PTMP WiFi PTP Outdoor Network CPE 2KM Transmission Distance With 12DBi High-Gain Antenna 2 LAN 100MBps Ethernet Port 24V PoE Power Supply CPE220 2 Pack